COD magnetic stirrer
Product number:
6051034
Manufacturer:
Behr Labor-Technik GmbH
Packaging information:
Weight:
0.727 kg
Description
The continuously adjustable COD series magnetic stirrer with 12 stirring points is used to mix the samples during the metering process. Due to its watertight casing and also its external power supply and control, it is suitable for use under water.
Properties
| Display: | Analogue |
|---|---|
| Manufacturer Article Number: | B00441223 |
| No. of stirring positions: | 1 |
| Type: | IMR 10 CSB |
| UNSPSC: | 41103806 |
| With timer: | No |
Skip product gallery
Chemical Oxygen Demand (COD) Standards
From
€155.40*
COD sample digestion units PA-CSB
From
€4,200.00*
COD workstations, PB-CSB/M
From
€6,372.00*
Thermoreactor CR 2200
From
€1,150.00*
Thermoreactor CR 4200
From
€2,020.00*
COD cooling trough
From
€96.80*
Workstations for SMA ARB
From
€61.00*
behr COD Heating Blocks
From
€1,374.00*
TRS 300 programmable temperature and time control unit
From
€1,435.60*
COD-Standard Cuvette Test, 16 mm
From
€79.80*
Similar products
These standards are ideal for use as control standards to verify that correct analysis for COD has taken place. Extensive range (10 to 60000 ppm), NIST traceable, 2 years shelf-life. Bottles of 500 ml.
Unit configuration for simultaneous digestion of maximum 6 or 12 COD samples in acc. with ISO, DIN etc.A digestion unit consists of the following components:TRS 300 microprocessor-controlled time and temperature control unit with COD programCSB/E Precision heating block for RG 2 reaction vesselsE/B Insert and yoke type frame for RG 2 reaction vesselsKW/N Cooling trough with holder and stands for E/BRG 2 Reaction vesselsLK 1 COD air coolersLS Air cooler stands for LK COD air coolers
For COD determination. Complete workstations for simultaneous determination of maximum 6 or 12 samples in acc. with ISO, DIN etc. Manual metering and titration.A workstation consists of the following componentsTRS 300 Microprocessor-controlled time and temperature control unit with COD programCSB/E Precision heating block for RG 2 reaction vesselsE/B Insert and yoke type frame for RG 2 reaction vesselsKW/N Cooling trough with holder and stands for E/BSM 12/N Series magnetic stirrer for E 12/B insert/yoke type frame (only for PB-CSB 12/M)RG 2 Reaction vesselsMRST 2 Magnetic stirrer rod set , 12 rodsSIST 100 Boiling stones , contents 100 gLK1 COD Air coolersLS Air cooler stand for LK COD air coolersPTFE 29 PTFE Collars for LK 1, set of 12 collarsTS COD Transport stands for E/B insert/yoke type frameHTI 1 Manual titration station
Routine device for waste water analysis. Thermoreactor with preset programmes for the digestion of standard parameters in reaction cuvettes. The CR2200 allows standard-compliant digestion with programmes for the standard parameters COD, total nitrogen, total phosphorus, TOC and heavy metals in galvanisation.1 thermoblock with 12 holes for reaction cells with an outer diameter of 16 mm8 stored programmes for all important digestions: 148 °C for 120 min; 148 °C for 20 min; 120 °C for 30 min; 120 °C for 60 min; 120 °C for 120 min; 150 °C for 120 min; 100 °C for 60 min, 100 °C for 30 minAutomatic temperature switch-off at the end of the set programmePower supply 115/230 VAC, 50/60 Hz
Thermoreactor with pre-programmed and user-defined programmes for the digestion of standard parameters in reaction cuvettes. The CR4200 allows standard-compliant digestions with programmes for the standard parameters COD, total nitrogen, total phosphorus, TOC and heavy metals in galvanisation. In addition, 8 separate programmes can be created for special digestions at temperatures between room temperature (25 °C) and 170 °C. Independent thermoblocks allow 2 different programmes to be run simultaneously.2 independent thermoblocks with 12 holes each for reaction cells with an outer diameter of 16 mm8 stored programmes for all important digestions: 148 °C for 120 min; 148 °C for 20 min; 120 °C for 30 min; 120 °C for 60 min; 120 °C for 120 min; 150 °C for 120 min; 100 °C for 60 min, 100 °C for 30 minAutomatic temperature switch-off at the end of the set programmeAQA/IQK with optional external temperature sensor for documentationPower supply 115/230 VAC, 50/60 Hz
The cooling trough prevents the overheating of the COD samples during the critical addition of sulphuric acid. In addition, it is used to cool the samples after the heating phase.
Workstation model SMA-ARBThe behrotest® workstation model SMA-ARB is a basic system for simultaneous aqua regia digestion of either 6 or 12 samples for heavy metals analysis.System components:Precision 6 or 12 sample SMA heating block for round-bottom sample vessels of Ø 41.8 mm, temperature range 20 to 300 °C.External ET 2 controller, operating range 20 to 399°C. Time settings from 10 to 120 min. and continuous operation.6 or 12 SR 2 250 ml round-bottom sample vessels with standard taper mouth and PVDF collar.6 or 12 RFK 1 Allihn reflux condensers.6 or 12 AS 1 absorption vessels.SG/B stainless steel vessel holding frame for 6 or 12 sample vessels.Support scaffold with cooling water distributor and storage holder for 6 or 12 condensers.Workstation model SMA-ARMThe behrotest® SMA-ARM workstations are provided with a programmable microprocessor-controlled time/temp. controller as well as a fume manifold for drawing off the acid vapors. This results in greater convenience and functionality in routine laboratory operations.
COD acc. to ISO Precision heating blocks with 6, 12 or 24 sample positions. Flat surface heater for even temperature distribution to each sample position. Stainless steel and powder coated steel casing. Extensive insulation provides for inoffensive temperatures of the casing surfaces.End-to-end grooves in the precision aluminum plate at the bottom of the bores simplify sample handling and provide for exemplary safety of the analyst:During sample insertion the grooves cause pressure compensation. Thus even the most accurately fitting reaction vessels slip easily into the bores, which is required to effortlessly handle the behr insert and yoke type frames for RG 2 reaction vessels.When inserting the samples into the hot heating block adherent moisture on the vessel surface evaporates in sudden bursts. The grooves drain off the vapor which otherwise might cause the vessels to jump up and down which might eventually lead to the destruction of the vessels.In case of one or more vessels overflowing the liquid COD samples discharge through the grooves minimizing the danger of damages inside the block caused by acids.
Programmable control unit for behrotest® digester blocks.behr one-button operation for particularly easy and quick programming. Menu navigation in the language of the country. 10 optionally configurable programs for block temperature and digestion time.The TRS 300 has a special COD program which has already been set by the plant. Therefore in the operation mode "COD" it heats up to a temperature which is 20°C above the set target temperature. After inserting the samples, the 20°C higher target value remains for another 6 minutes. This procedure ensures heating up to 148°C within 10 minutes which is specified by the ISO norm, and at the same time causes extremely high temperature constancy during the subsequent reaction process. The supplied Windows software permits the user to transfer time/temperatures profiles, which are specifically for the application, via the RS232 interface in both directions between one or more units (TRS 300) and a PC. Temperature data can also be transmitted from the unit to the PC via the RS232 interface while operating. The user can save them if necessary and print them out as graphics. Integrated safety function switches the connected units off if there is a short-circuit and an interruption of the temperature sensor.
Due to the chemical properties suitable for various photometers (e.g. Lovibond®, Hach®) with 16 mm tube diameter.
